Arcam A28 Betriebsanleitung PDF herunterladen (Seite 11)

E-11

English

Adjusting listening settings

e A28 allows you to customise various features of the

amplier to t your system. Use this diagram to help you

navigate through the available conguration options.

In the diagram, the control knob is shown as .

Normally, the display shows the source and the current

volume.

Press MENU once to enter the setup menu, use the

control knob to cycle through the menu items. When

A28 setup

you have found the setting that you wish to adjust (as

shown on the front panel display), press OK. To adjust

the chosen setting, use the control knob. Press MENU to

store the change and return to volume display mode – or

press OK again to move to the next setting.

Note that the menu will time-out aer a short period

without pressing a button or adjusting the control knob,

with the display reverting to the current volume.

e following items can be adjusted from the setup

menu:

Conguring your A28 amplier

Balance

is allows you to adjust the output balance between le and right channels. e balance

control is also available directly by pressing the front panel BALANCE button.

Vol Res ere are three volume-display options to chose from: ‘Std’, ‘Fine’ or ‘Ref’. Standard and

Fine represent dierent levels of volume-control sensitivity; the Reference setting gives

absolute increments in 0.5dB steps.

I/P Trims

Input trims are used to compensate for variations in output levels of dierent source

equipment. If, for example, your CD player is louder at a given volume display value

than other inputs, you can attenuate it by using this setting so that it matches your other

components.

Use the source-select buttons to select the input you wish to adjust, then the control knob

to set (increase or decrease) the input volume for that source.

Proc Mode

Processor mode enables you to x the gain (volume setting) of your A28. e A28 (in

combination with a power amp.) can then be used to drive the front le and right speakers

of a surround-sound system, when fed from a separate processor. e volume of the entire

system can then be controlled using the processor.

Feed the sound from the processor into the AV input, then set the gain of the A28 to match

the ampliers that drive your other loudspeakers.

REC SRC

To record one source while listening to another, turn the control knob until the display

shows ‘Rec ’ followed by the name of the input (Sat, Phono, CD, Tuner, AUX or DVD)

that you wish to record from. e record source control is also available directly by

pressing the front panel RECORD button.

Max onvol

is can be used to limit the maximum volume the amplier operates at when it is rst

switched on: the A28 comes on at the (reduced) ‘Max. On Volume’ level if the last-used

volume exceeds this value.

If this item is set to ‘Off’, the A28 always comes on at the last used volume, even if this is

very loud.

Reset Conrming ‘Yes’ restores all amplier settings to their factory defaults.

VOLUMEOOO

BALANCEOO

VOL RESOO

I/PoTRIMS

PROC MODE

MAX ONVOL

RESET0000

L , ; , R

RES REF

RES FINE

RES STD

AUX TRM -8 . . . 8

PROC AV

FIXED 3 . . . 72

ONVOL OFF

ONVOL 3 . . . 72

NO YES

REC SRC

REC SATPHONOCD

TUNERAUXDVD

‘Power On’ state

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 17

Kommentare zu diesen Handbüchern

Keine Kommentare

Arcam A28 Betriebsanleitung Seite 11

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audioverstärker Arcam A28